|
Dry Hydrant Accessories
Dry Hydrant Signs & Decals
Dry Hydrant Signs & Decals |
Part
Number
|
Description |
|
9145-002 |
"No
Parking"
Reflective DH Decal
6"x12" |
|
9145-001 |
"No
Parking"
Reflective Metal DH Sign 12"x18" |
|
9145-004 |
"Do
Not Back Flush" Decal |
Support Clamp – Stainless Steel
Support Clamp –
Stainless Steel |
Part
Number
|
Description |
| 9152-001* |
6"
Strainer Support Clamp |
| 9152-002* |
8"
Strainer Support Clamp |
*Rod furnished by customer
– Use any 1" Dia. O.D. pipe.
Suction Vent/Valve – (For use priming Check
Valve Strainers)
Aluminum Coupling - designed to be connected between
the large intake on the engine pump and the suction hose. Vent port
uses a 1 ½" x ¼ turn ball valve. To Use:
1 - Connect to intake with hose attached to Dry Hydrant. 2 - Open
¼ turn vent valve. 3 - Open tank to pump valve. 4 –
Water will flow from onboard tank, filling up dry pipe as air escapes
through the vent. When air turns to a solid stream of water, close
¼ turn ball valve. 5 - Close tank to pump valve. Pump should
start without pulling prime. If not, momentarily pull primer.
Assembly normally is made using long handle FNST x MNST thread,
however other configurations are available upon request.
Suction Vent/Valve |
Part
Number
|
Description |
|
9289-000 |
6"
Vent Valve Assy – M/F L/H |
|
9289-010 |
5"
Vent Valve Assy – M/F L/H |
|
9289-020 |
4 ½"
Vent Valve Assy – M/F L/H |
|
9289-030 |
4" Vent
Valve Assy – M/F L/H |
Female/Female NST, Storz or
Cam Lock also available upon request.
Fistular Dry Hydrant Installation - "Patented"
–
The Swivel Kit is designed for special applications where the strainer
is not desired to be in the water all of the time. It works like
a giant suction straw. It rests in place until needed. To use, you
simply pivot the strainer end up, around and slide it gently into
the water. The device uses a 180 Deg Dry Hydrant Head but can use
a variety of strainers. The picture below shows a 6" Horizontal
Strainer.
The kit includes the Swivel and Pivot Device along with two Cradles.
Cradles are used to support the pipe and strainer in both the "at
rest" and "in use" positions. System as shown uses
one 20 ft section of 6” Schedule 40 PVC Pipe. Great for salt
water applications.
Part Number
|
Size |
Description |
| 9182-000 |
6" |
Swivel Kit - Fistular
Dry Hydrant |
Typical installation noted below:
Installation
at rest
|
Swivel/Roller
Mechanism |
Ready
for Suction Hose |
|
|
|
Male Dry Hydrant – Locking Cap Feature
 All
Male Dry Hydrants can be prewired with a locking cap cable upon
request. Locking mechanisms can be tear away tamper seals (normally
seen on fire Extinguishers) or break away locks (as seen in the
picture). Locks not included. To order request "Special W/Locking
Cap Feature".
Price: Add $7.00 to the cost of selected
Dry Hydrant.
360 Degree Swivel Joint (Speeds Hose Connection Time)
6" Schedule 40 PVC Pipe with Black Anodized Aluminum Swivel
in
center. Assembly has grease fitting for maintenance.
Head can glue directly to one end.
360 Degree Swivel Joint |
| PART
# |
SIZE |
DESCRIPTION |
| FTS-600 |
6" |
360 Deg In-line
Swivel
6" Schedule 40 PVC Pipe
Both ends |
Works great for bridge applications.
Flush Mount Dry Hydrant Enclosure Kit
 For
installations where extensions above the ground are not wanted.
Reduces Vandalism for problem areas. Mounts flush with ground. 18"
Dia Heavy Wall Polyethylene enclosure with Cast Iron Cover. Works
best with 180 or 45 Deg Dry Hydrants. Male or Female. Kit comes
with Drain Screen and No Parking Decal.
Part Number
|
Size |
Description |
|
9161-000 |
18" |
Flush Mount
Enclosure
18" dia. x 20" deep |
PVC/Flex Joint - Dry Hydrant Installation
Many applications call for the use of a flexible suction hose.
The one shown here is designed to glue into a 6" or larger PVC pipe.
The 3 ft. section comes complete with 6" PVC Straight Pipe Connections
on each end. The collars are the same as used on the suction hoses
and can be changed in the field if needed. The black helical hose
is translucent and water can be seen as drafting proceeds. This
device is great for salt-water applications and/or other needs where
strainer location or depth is a concern.
Part Number
|
Size |
Description |
| 9181-000 |
6" |
PVC/Flex
Joint Assembly |
|
|
|
|
Installation
in normal "up" position
Dry Hydrant in foreground
|
Horizontal
view of installation
Pulley allows strainer to be lowered |
|
|
|
Basket Strainer on end |
Strainer
lowered into the
water ready for use |
|
|
3 ft. PVC/Flex Joint as purchased |
End
view with collar |
Mooring Buoys - Dry Hydrant Installation
Mooring buoys can be used for a variety of reasons. They are great
to indicate the end of a strainer in busy waterways or can be used
to support a suction hose or strainer when debris or silt is a concern.
It may also be used with the "PVC Flex Joint" to maintain
a constant suction depth for Dry Hydrant installations.
Buoys are hard skinned and almost indestructible. Buoys are made
from high-density polyethylene, filled with closed cell foam. White
with blue florescent stripe. Highly visible to navigation. All come
complete with 3 ft of heavy-duty 2" plastic chain. Available
in 12", 15" or 18" Diameters.
Mooring Buoys |
Assembly Number
|
Diameter |
Buoyancy |
| 9769-612 |
12 Inches |
30 Lbs |
| 9769-615 |
15 Inches |
60 Lbs |
| 9769-618 |
18 Inches |
100 Lbs |
|
